Hasegawa's 1/48 scale
Messerschmitt Bf 109 G-4/R6
'Regia Aeronautica'

by Werner Scheibling

Hasegawa's 1/48 scale Messerschmitt Bf 109G-4 is available online from Squadron.com

This is Hasegawa's 1/48 scale Messerschmitt Bf 109G-4/R6 kit, from the 'special version' series. It comes with additional resin parts and decals relating to two planes that flew with the Italian Regia Aeronautica in the last months before Mussolini's Fascist Empire collapsed with the Armistice of 8^th September 1943. 

One of these, the original 365-1, is well documented in an often-published colour photo of WW II origin which shows it parked in the open on Sciacca airfield.

When the Allied invasion forces secured this airfield in July 1943, they drew up a detailed record of the majority of the Messerschmitt 109 fighters found there. Because of these records, 365-1 can be clearly identified as a Bf 109 G-4/R6, Werk-Nr. 19566. It served with the 150^o Gruppo Autonomo from 23^rd May 1943 until early July, making it the longest lived Bf 109 in Regia Aeronautica Service. 

The Allied intelligence commission described 365-1's condition as 'fair but tail damaged', and indeed the photo shows two small red-brown patches on the rudder's left side. I would interpret these patches as repaired battle damage – bullet holes patched up with red-brown fabric or fabric doped with red-brown primer. 

The fate of 365-1 is not known, but it can be assumed that the aeroplane, though flyable, ended up on Sciacca's huge scrap yard amongst other Bf 109s and Macchi C.200s and 202s.

The Kit 

This 'special version' kit found its way into European shops in the summer of 2004 and consists of all the sprues you would normally find in the box of a regular G-6 kit. Highlights and shortcomings of this kit have been described many times over the years so I won't repeat them here. 

Additional parts which enable the modeller to turn this kit into an earlier G-4 are nicely cast in yellowish, rather tough and flexible resin. These are: The upper cowl decking with gun troughs for two 7,92 mm MG17 and two main wheels with spoked hubs and treaded tyres.  

My enthusiasm for the resin parts cooled noticeably when I found out that the cowl decking was a whole millimetre too short at the rear and too narrow to fit the fuselage properly. I had to fill the millimetre gap with styrene sheet and build up the right side with Milliput epoxy putty. It took hours of delicate filling and sanding to make the glue seam – which doesn't fall on a panel line - finally invisible. Gunze-Sangyo's 'Mr. Resin' primer, applied in several layers by airbrush and sanded down after each application, finally did the job.

I have my doubts whether the described fault can be explained by 'resin shrinkage', as the kit was brand-new off the shelf. Hasegawa would have done a much more appreciable job if they had added the proper injection moulded parts from their G-2 kit. Both resin wheels had tiny casting imperfections which resulted in a 'broken' spoke in each. Luckily this fault is hardly noticeable once the parts are painted and weathered.  

Unfortunately I have to continue moaning as the decal sheet was practically unusable. All white characters - and there are a lot - were printed in some kind of cream colour which would have stood out drastically next to painted white wingtips and a white fuselage band. Testing some of the decals showed that they also silvered strongly once dry. This is not what can be expected from a company that is generally referred to as one of the top three – both in quality but unfortunately also also in price.

Cockpit / Fuselage 

The rather simple cockpit parts provided by Hasegawa had to make place for a much nicer resin cockpit produced by Aires. Cockpit sidewalls, floor and related components are beautifully cast in rather brittle cream coloured resin and - together with additional photo-etched items - make up into a convincing replica of the original.

Click on the thumbnails below to view larger images:

Further Alterations: 

·        Installation of 'Moskit' real metal exhausts with thinned down exhaust shrouds.

·        A cutout for the tail wheel well. 365-1 featured the early style open wheel well which is untypical for a G-4. A section of styrene tubing was epoxied into the wheel well to act as a recipient for the brass tail wheel strut.

·        A round hatch had to be scribed on the righthand rear fuselage side to represent the filler hatch for compressed air necessary to charge the twin MG 17 guns.

·        The spinner once started life as part of a so-called 'corrected prop and spinner' set cast in resin by Cutting Edge. The difference to the original Hasegawa part is a slightly less curved profile, resulting in a diameter smaller by a mere 0,1mm at the middle. I doubt that the difference between the two parts can be seen with the eye. I had to measure the resin replacement with callipers to believe it.

If Cutting Edge would have wanted to do a really nice job they would have changed the cutouts for the prop blades (which were not symmetrical) and fitted a proper blast tube for the engine mounted MG 151/20. I fixed these shortcomings and then did something with silicone rubber and resin that made spending 5 dollars much more palatable. I did not use the Cutting Edge prop blades as they look too wide compared to pictures of early 109 G's.

Click on the thumbnails below to view larger images:

Wings 

·        The main wheel wells were refined by adding strenghtening ribs to the inside of the upper wing. The concave shape of the wing bulges was modelled with a round grinding bit.. Four lightening holes along each of the recesses for the u/c legs were drilled out and tiny styrene stubs, representing the u/c locking pins, added. The zipped canvas covers along the rear of each wheel well were modelled with appropriately engraved 0,1 mm styrene sheet.

·        I used cut-offs from clear styrene sprue to represent the wing tip position lights. First I drilled a 0,3 mm hole into the clear material and filled it with paint (blue-green starboard and red port). Then I glued the clear part into cutouts I had prepared in the wing tips, sanded everything into shape and polished the clear styrene to a high shine.

·        Using the wing parts as they are would result into far too flat a dihedral. Both wing roots had to be sanded down considerably to achieve the proper 'V'-angle.

·        I added stiffeners and air-flow guide panels to the otherwise completely bare radiator outlet flaps. Large sink marks in both landing flaps had to be filled and sanded – a fault that seems to be common with this kit.

Click on the thumbnails below to view larger images:

Wing armament ('R6 = Rüstsatz 6') 

To add a point of interest to my model I decided to open up one underwing gondola and show the MG 151/20 installation.  

I could not come up with any technical drawings, so had to rely solely on one b/w photo that shows two technicians working on the left wing gun of a Mediterranean based Bf 109G. The photo is good enough to show how this weapon was installed in the narrow (left wing) gondola: The gun lay on its left side and the ammunition belt fed straight down into the breech. The empty ammo belt was fed into a chute that was angled by 90 degrees and ejected the empty cases and links towards the centre of the aircraft. The rather un-aerodynamic airstream-deflectors around the ejection chute allowed the empty ammo belt to disintegrate properly before it could be grabbed by the air stream. Without these deflectors the cannons tended to jam after a few rounds. 

Hasegawa's parts are basically correct in outline, but I had to relocate the ejection chute and scratch-build the deflectors from 0,1mm styrene sheet. The open inspection hatch was crash-moulded with thin plastic sheet. 

Aires offers a set of four very detailed MG 151/20 guns in resin, which fit perfectly into the wing gondola. The gondola just needed a little hollowing out with a rotating tool. I replaced the gun barrels with 0,8 mm hypodermic needle tubing, as the original resin parts are overscale. 

The leather or fabric shrouds covering the gondola openings around the gun barrels were replicated with carefully applied PVA glue. This stuff shrinks slightly during drying and looks convincingly like crinkly leather or fabric after painting.

Click on the thumbnails below to view larger images:

Undercarriage 

·        The undercarriage was refined with thinner scratch-built covers and hydraulic lines made from 0,2 mm copper wire. The wheels were connected to the legs with short stubs of brass wire. Doing this, I also corrected the u/c leg – wheel distance and angle.

·        The tail wheel was customized by removing the 'canvas' boot protecting the oleo leg and its scissors – just like on the real 365-1. A length of 0,8 mm brass wire was used to form the strut and the scissors were constructed from styrene sheet.

While studying available photos of Regia Aeronautica Bf 109 Gs, I stumbled upon some sort of modern myth: All the decal sets for Italian 109 Gs I have seen so far represent the wing fasces as surrounded by a segmented circle. The photos I've checked show that Italian 109Gs were adorned with completely standard wing insignia sporting a normal black circular surround. I also do have my doubts whether the original German top wing crosses were as neatly oversprayed as generally depicted. Still I preferred the somewhat more perfectionist look to an irregular grey patch. The lower wing fasces were applied after the whole wing panel was oversprayed in a somewhat lighter shade of grey. Both rear fuselage sides (roughly from aerial mast to vertical stabilizer) were oversprayed with an Italian shade of light grey and an imitation of the original German mottle scheme in darker greys.

I also resisted representing the aforementioned tail damage as I didn't want to ruin the looks of that interesting aeroplane. 

My model was airbrushed entirely with 'Vallejo Model Air' acrylics and an Iwata Eclipse HP-BS. I can only comment that these are the best paints I've ever worked with and I now prefer them even to my up-to-now favourite brand of LIFECOLOR. 

Decals came from Sky Models' 'Italian Bf 109Gs' sheet. The printing quality is first rate, as always, even though the carrier film turned out to be somewhat thicker than usual. It took plenty of Aeromaster's 'AeroSol' (which is really strong stuff) to force the decals down into the panel lines. 

Panel lines and weathering were done with various shades of pastel dust. Only very few areas – such as the cockpit, wheel wells and undercarriage – were treated with light washes of artist's oils.

Kit, Accessories and Decals 

·        Hasegawa 1/48 kit 'special version' #09559 Messerschmitt Bf 109 G-4 Regia Aeronautica

·        Aires 1/48 resin and PE cockpit set #4034, Messerschmitt Bf 109 G

·        Aires 1/48 resin set #4021, German 20mm gun MG 151/20

·        Sky Models 1/48 decal sheet #48011, Messerschmitt Bf 109 G/K in Italian Service

·        Moskit 1/48 metal exhausts #48-02, Messerschmitt Bf 109 F/G/K

References 

·        Ali Straniere in Italia No. 1, Messerschmitt Bf 109 Italiani, by Gregory Alegi and Marco Gueli, La Bancarella Aeronautica Torino, 2002

·        Regia Aeronautica Caccia & Assalto 1940-1943, Parte II, by Paolo Waldis, Marino De Bortoli and Angelo Brioschi, La Bancarella Aeronautica Torino, 2003

·         Aero Detail No. 5, Messerschmitt Bf 109 G, by Shigeru Nohara and Masatsugu Shiwaku, Dai Nippon Kaiga Co. Tokyo, 1992
ISBN: 4-499-20589-1

·        Messerschmitt Me 109, Alle Varianten von Bf 109 F bis 109 K, by Willy Radinger and Wolfgang Otto, Aviatic Verlag Oberhaching, 1998

ISBN: 3-925505-43-1

Click on the thumbnails below to view larger images:

Messerschmitt Bf 109 Modelling Manuals 17 US Price: $17.95 UK Price: £12.99 Publisher: Osprey Publishing Publish Date:  January 25, 2002 Details: 64 pages; ISBN: 1841762652 Shop Buy it from Osprey Publishing

Model, Images and Text Copyright © 2004 by Werner Scheibling
Page Created 06 June, 2005
Last Updated 24 December, 2007

Back to HyperScale Main Page